- #AXIS CAMERA STATION YELLOW DOT CONTINUOUS RECORDING HOW TO#
- #AXIS CAMERA STATION YELLOW DOT CONTINUOUS RECORDING INSTALL#
- #AXIS CAMERA STATION YELLOW DOT CONTINUOUS RECORDING UPDATE#
- #AXIS CAMERA STATION YELLOW DOT CONTINUOUS RECORDING MANUAL#
#AXIS CAMERA STATION YELLOW DOT CONTINUOUS RECORDING MANUAL#
Set “video mode” as manual or auto in the WEB interface.īlack edge appears in the image after upgrade.Įliminate IPC configuration or restore factory default after upgrading program. Set “video time period”, “snapshot time period” in the WEB interface please refer to the for more details.Ĭheck if the “memory point” enable in the WEB interface is checked.Ĭheck if the connection of SD and FTP of video and snapshot storage is normal, try to connect FTP to the computer. “Snapshot time period” is set wrongly storage path is not correct “video mode” is set as off. The device failed to record video and snapshot. At this moment, you should adjust the elevation angle of the lens or place the device on the edge When you use the device on the table (especially rough surface), the IR light will shoot back to the lens, which will cause bad IR effect and white picture. IR-CUT is set as color mode, which caused the front-end sensor to fail to sense IR light. The object is so far that it is out of the range of IR light. Users didn’t use specified power supply, and failed to enable all the IR lights. Too many users logging in, and it is beyond the device code stream output capacity.ĭisconnect the network or restart the device repeatedly, see 1.1 for more details. Network bandwidth is not enough change a switcher with bigger bandwidth. It displays “Resources are limited, failed to open video” after I log in the IPC.
#AXIS CAMERA STATION YELLOW DOT CONTINUOUS RECORDING INSTALL#
Please run IE as administrator for WIN 7, you need to install QuickTime plug-in if it is non-IE browser. There is no code stream when I log in and the network program restarts constantly after upgrade.Ĭheck if there is IP conflict or network disconnection.Ĭheck if each connection line is loose inside the device after disassembling the camera.Ĭheck if the application program of IPC is corresponding to the model, and check if N/P format program is correct.Ĭheck if the control and WEB are correct, there is control running permission under WIN7, you can delete the control under C:\Program Files\webrec and eliminate IE buffer memory to reload control and WEB. I can use “Ping” to test that the IPC is on line after upgrade, but fail to log in. Log in again to check if upgrade is successful, because sometimes the progress bar doesn’t show feedback in time due to the network environment.Ĭheck if the network environment is normal, and there is disconnection or power failure during upgrade.Ĭheck if the program and the device are matched. My IP Camera is off line from time to timeĬheck if the network environment is good and the network cable hole plug of IPC end is loose.Ĭheck if the device is under normal power supply.Ĭheck if the device upgraded to a wrong program.
#AXIS CAMERA STATION YELLOW DOT CONTINUOUS RECORDING UPDATE#
![axis camera station yellow dot continuous recording axis camera station yellow dot continuous recording](https://www.arri.com/resource/blob/182400/903f60b8a3cf789afc2b362b2cb9e062/camera-faq-minilf-recording-formats-fps3-data.png)
Diagonal or Horizontal Striping on Live Feed.Camera Does Not Switch Between Day and Night Mode.
#AXIS CAMERA STATION YELLOW DOT CONTINUOUS RECORDING HOW TO#
How to Convert and Playback Backed Up Video.
![axis camera station yellow dot continuous recording axis camera station yellow dot continuous recording](https://i.ytimg.com/vi/zxqO_3fCDRQ/maxresdefault.jpg)
![axis camera station yellow dot continuous recording axis camera station yellow dot continuous recording](https://kb.synology.com/helpfile/SurveillanceStation/8.2.9-7265/SurveillanceStation/images/recording_event_detection/figure04.png)